Getting more bands out of a 40m OCFD (Windom)

The original design in my book for a flat-top
optimised 40m OCFD (click for larger image).

In my book “Introduction to Antenna Modelling” I talk about how you can get more bands out of a 40m off centre fed dipole (OCFD – sometimes incorrectly called a Windom) by adjusting the feed point position.

The conventional feed point is at the 33%/66% point, but if you do that with a 40m OCFD (roughly 20m long) you find that you get 40m, 20m and 10m, but 15m offers a high SWR.

But the model shows that by adjusting the feed point to 41% you can get a low SWR on 15m too.

But this is just theory – does it work in practice?

I thought I would try it in real life and see how it performs. The only trouble is I wanted to erect the antenna as an inverted V, so would that affect the lengths and feed point in the MMANA-GAL model?

Anyway, after an afternoon of fiddling with MMANA-GAL I ended up with an answer – an antenna with a total length of 20.75m (8.5m and 12.25m for a 41%/59% feed point), fed with a homemade twin core 4:1 balun and mounted at about 8.5 metres, fed with about 25m metres of Mini8 coax.

The model I ended up with suggested low-ish SWRs on 40 (actually, just over 3.1:1), 20, 15 and 10m, with not so good matches on 30m and 17m, as expected.

Now to turn it into a real antenna. If you use PVC-coated wire, you'll end up with an antenna that has to be shorter than calculated due to its velocity factor being less than one. That is, the speed of light is slower in a denser medium.

Every antenna I have ever designed with MMANA-GAL has ended up shorter than calculated.

So applying an estimated velocity factor of 95% I ended up with two legs of 8.075m and 11.637m. I cut the wires a little longer than this and twisted the ends over to allow for a little adjustment – I fully expected to have to shorten the wires once it was up.

Having hauled it all into position at the top of a fibreglass fishing pole I checked the SWR at the end of the coax and was pleasantly surprised. It was pretty much spot on, with an SWR less than 3:1 on 40, 20, 15m and 10, and my internal ATU could also tune 30m and 17m, although obviously its performance is down a little on those bands.

Lengthening it a little might put the lowest SWR points a little more mid-band, but we are only talking about fractions of one SWR point.

The model shows it is a cloud warmer on 40m (good for NVIS contacts), and the multi-lobe pattern on the higher bands is complex and not always ideal for DX, but this is a compromise antenna.

Early tests have been promising, with the antenna performance matching dedicated dipoles on the bands on which it is resonant. So I think it is a success.

Actual SWR figures (at end of 25m of coax)

7.100MHz 1.9:1

10.120MHz 3.3:1

14.175MHz 2.5:1

18.100MHz 3.0:1

21.225MHz 1.2:1

24.940MHz 2.2:1

28.500MHz 1.4:1

Update: Well, I've been using it for a day and have worked Cuba (CO), Moldova (ER), Qatar (A71), Saudi Arabia (HZ) and Ceuta & Melilla (EA9) on 15m where it seems to go great guns. 40m has given strong contacts into Europe. I like it.

Update, February 2016
I've now been using the antenna for about four months so here is an update. It works very well on 40m, and is consistently equal to or down about 0.5 S point on my W5GI. I haven't used it much on 10MHz, but it looks to be slightly better than the W5GI. It works very well on 14MHz and 18MHz and is really good on 21MHz. Again, I haven't used it much on 12m, but it plays on 10m, although it is consistently slightly worse than a dedicated half-wave dipole by about 1-2 S points. Overall, not bad for a multi-band antenna.

A typical 4:1 two-core Guanella balun.

As you can see below, someone asked about the balun. It is a Guanella design wound on two FT140-43 cores. Each core has about 13 turns (from memory) of twin loudspeaker wire.

The cores are then put back to back and wired with one side in series and the other in parallel. If the characteristic impedance of the twin wire is about 100 Ohms this gives the required 200 Ohms/50 Ohms = 4:1 impedance transformation.

The current thinking is Ferrite Type 61 for the top end of the HF range; Type 43 for the bottom end; or Type 31 for the best compromise across the range. The image is not of my balun but it is of a similar design. Mine is housed in a box with all the joints sealed with tape for waterproofing purposes.

RSGB Convention, October 2015

I gave two talks at this year's RSGB convention. The first was on HF Propagation and I'd like to remind readers that I have a video presentation with audio that is available for RSGB-affiliated clubs.

If you would like your club to have a copy get your programme secretary to drop me an email at steve [at] infotechcomms.co.uk. I can also do a Skype-based Q&A after the presentation in most cases.

Otherwise, there is always the free "Understanding LF and HF Propagation" e-book to download.

The other presentation was on "An introduction to antenna modelling with MMANA-GAL". This is available for download. Don't forget that my three books are also available from RSGB ;-) or you can use the links on the right.